Documents techniques
Spécifications
Brand
EMERSON – ASCOTension d'alimentation
24 V dc
Nombre d'orifices
3
Taille de connexion
1/8in
Raccord
G 1/8" femelle
Commande
Direct
Version
NC
Type d'application
Air, gaz inerte, Huile, Eau
Type d'application
3/2
Diamètre d'orifice
1.6mm
Séries
356
Matériau du corps
Brass
Pression de service maximale
10 bar
Plage de fréquence de fonctionnement
-10 → +100 °C
Température maximale d'utilisation
+100°C
Genre du raccord
Female
Température d'utilisation minimum
-10°C
Filetage ou type de raccord
G
Temps d'ouverture maximum
10ms
Temps de fermeture maximum
10ms
Facteur de débit Kv
0.08m³/h
Détails du produit
Electrovannes 3//2 à commande directe série 356
Gamme d'électrovannes 3//2 NF à commande directe.
Encombrement réduit et faible poids, pour faciliter l'installation.
Pas de pression minimale de commande.
Commande manuelle en standard.
Corps en laiton.
Connecteur débrochable.
Fixation par 2 trous tarandés sur la partie inférieure.
3 Way Inert Gases and Fluid Valves
Compact solenoid valves suitable for most gas and fluid handling applications. Where practical, valves are shown with a schematic diagram showing the (circuit) function. The diagram is laid out so that the left hand side of the diagram describes the valves operation when the coil is energised. When the coil is de-energised, the spring (or servo-assist) return controls the valve and this is described on the right hand side of the diagram, see the typical schematic diagram below.,The 3//2-way designation indicates a valve with three ports and two modes of operation. It is normal practice to refer to 2//2-way valves as two-way.,The port designations A, B, P, P1, P2 and R are used on the schematic diagrams and are marked on the valve bodies. Valve bodies are marked for a specific circuit function but can often be used for other functions. Reference to the schematic diagrams and technical specifications will indicate the appropriate connections and pressure capabilities should an alternative circuit function be required.
Prix sur demande
1
Prix sur demande
1
Les informations sur le stock sont temporairement indisponibles.
Veuillez vérifier à nouveau plus tard.
Documents techniques
Spécifications
Brand
EMERSON – ASCOTension d'alimentation
24 V dc
Nombre d'orifices
3
Taille de connexion
1/8in
Raccord
G 1/8" femelle
Commande
Direct
Version
NC
Type d'application
Air, gaz inerte, Huile, Eau
Type d'application
3/2
Diamètre d'orifice
1.6mm
Séries
356
Matériau du corps
Brass
Pression de service maximale
10 bar
Plage de fréquence de fonctionnement
-10 → +100 °C
Température maximale d'utilisation
+100°C
Genre du raccord
Female
Température d'utilisation minimum
-10°C
Filetage ou type de raccord
G
Temps d'ouverture maximum
10ms
Temps de fermeture maximum
10ms
Facteur de débit Kv
0.08m³/h
Détails du produit
Electrovannes 3//2 à commande directe série 356
Gamme d'électrovannes 3//2 NF à commande directe.
Encombrement réduit et faible poids, pour faciliter l'installation.
Pas de pression minimale de commande.
Commande manuelle en standard.
Corps en laiton.
Connecteur débrochable.
Fixation par 2 trous tarandés sur la partie inférieure.
3 Way Inert Gases and Fluid Valves
Compact solenoid valves suitable for most gas and fluid handling applications. Where practical, valves are shown with a schematic diagram showing the (circuit) function. The diagram is laid out so that the left hand side of the diagram describes the valves operation when the coil is energised. When the coil is de-energised, the spring (or servo-assist) return controls the valve and this is described on the right hand side of the diagram, see the typical schematic diagram below.,The 3//2-way designation indicates a valve with three ports and two modes of operation. It is normal practice to refer to 2//2-way valves as two-way.,The port designations A, B, P, P1, P2 and R are used on the schematic diagrams and are marked on the valve bodies. Valve bodies are marked for a specific circuit function but can often be used for other functions. Reference to the schematic diagrams and technical specifications will indicate the appropriate connections and pressure capabilities should an alternative circuit function be required.