Transformateur d'éclairage, Vin 230V c.a., Vout 11.5V, 20 → 70W

Documents techniques
Spécifications
Brand
RS ProTension au primaire
230V ac
Tension au secondaire
11.5V
Puissance
20 → 70W
Dimensions
53 x 22 mm (Ø)
Profondeur
22 mm
Exigence d'une charge minimale
20W
Température maximum
+45°C
Masse
70 g
Type d'application
Electronic
Gradation
Dimmable
Méthode de gradation
Bord de fuite
Diamètre
53mm
Fréquence de fonctionnement minimale
50Hz
Type de raccordement
Fil de sortie
Caractéristiques de protection
Protection contre les surtensions, protection contre la surchauffe, protection contre les surcharges, protection contre les courts-circuits
Fréquence de fonctionnement maximum
60Hz
Pays d'origine
Italy
Détails du produit
Mini-transformateur électronique réglable rond à sortie simple
Transformateur indépendant IP20 pour lampes halogènes de 12 V
Protection classe II contre les chocs électriques suivant des contacts directs et indirects
Le transformateur est fourni avec des câbles sur les circuits primaires et secondaires
Excellente fiabilité de fonctionnement à des températures très élevées (Ta = 45 °C ; Tc = 90 °C)
Modèle compact
Assemblage et installation faciles
Protégé contre la surchauffe, les courts-circuits, les pics de tension et les surcharges
Low Voltage Lighting Transformers
Dimming Methods (where applicable):
Leading Edge:
The control device is either a thyristor or triac which blocks power until they are switched on by the control signal. At that point the current flows almost instantaneously and continues to flow until the end of the half cycle of the mains waveform. When the signal reaches zero, the device turns off and no more current is passed until it is triggered again. Turning the power on and off in this manner averages out creating a constant intensity level and by altering the precise trigger point over a period of time the lamp can be dimmed.
Trailing Edge:
Since this method of dimming uses transistor technology it is not limited to just switching, therefore current can be controlled gradually. Transistors can be programmed to pass current at the start of each half cycle, and gradually switch off later. This will control the full amount of power reaching the lamp without the side effects of a step increase in current.
Prix sur demande
1
Prix sur demande
Les informations sur le stock sont temporairement indisponibles.
1
Les informations sur le stock sont temporairement indisponibles.
Documents techniques
Spécifications
Brand
RS ProTension au primaire
230V ac
Tension au secondaire
11.5V
Puissance
20 → 70W
Dimensions
53 x 22 mm (Ø)
Profondeur
22 mm
Exigence d'une charge minimale
20W
Température maximum
+45°C
Masse
70 g
Type d'application
Electronic
Gradation
Dimmable
Méthode de gradation
Bord de fuite
Diamètre
53mm
Fréquence de fonctionnement minimale
50Hz
Type de raccordement
Fil de sortie
Caractéristiques de protection
Protection contre les surtensions, protection contre la surchauffe, protection contre les surcharges, protection contre les courts-circuits
Fréquence de fonctionnement maximum
60Hz
Pays d'origine
Italy
Détails du produit
Mini-transformateur électronique réglable rond à sortie simple
Transformateur indépendant IP20 pour lampes halogènes de 12 V
Protection classe II contre les chocs électriques suivant des contacts directs et indirects
Le transformateur est fourni avec des câbles sur les circuits primaires et secondaires
Excellente fiabilité de fonctionnement à des températures très élevées (Ta = 45 °C ; Tc = 90 °C)
Modèle compact
Assemblage et installation faciles
Protégé contre la surchauffe, les courts-circuits, les pics de tension et les surcharges
Low Voltage Lighting Transformers
Dimming Methods (where applicable):
Leading Edge:
The control device is either a thyristor or triac which blocks power until they are switched on by the control signal. At that point the current flows almost instantaneously and continues to flow until the end of the half cycle of the mains waveform. When the signal reaches zero, the device turns off and no more current is passed until it is triggered again. Turning the power on and off in this manner averages out creating a constant intensity level and by altering the precise trigger point over a period of time the lamp can be dimmed.
Trailing Edge:
Since this method of dimming uses transistor technology it is not limited to just switching, therefore current can be controlled gradually. Transistors can be programmed to pass current at the start of each half cycle, and gradually switch off later. This will control the full amount of power reaching the lamp without the side effects of a step increase in current.